Altera DDR SDRAM High-Performance Controllers and ALTMEMP Manuale Utente Pagina 48
- Pagina / 140
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
5–2 Chapter 5: Functional Description—ALTMEMPHY
Block Description
External Memory Interface Handbook Volume 3 June 2011 Altera Corporation
Section I. DDR and DDR2 SDRAM Controllers with ALTMEMPHY IP User Guide
Block Description
Figure 5–1 on page 5–2 shows the major blocks of the ALTMEMPHY megafunction
and how it interfaces with the external memory device and the controller. The
ALTPLL megafunction is instantiated inside the ALTMEMPHY megafunction, so that
you do not need to generate the clock to any of the ALTMEMPHY blocks.
The ALTMEMPHY megafunction comprises the following blocks:
■ Write datapath
■ Address and command datapath
■ Clock and reset management, including DLL and PLL
■ Sequencer for calibration
■ Read datapath
Figure 5–1. ALTMEMPHY Megafunction Interfacing with the Controller and the External Memory
External
Memory
Device
ALTMEMPHY
Write
Datapath
Address
and
Command
Datapath
Clock
and Reset
Management
Sequencer
Read
Datapath
Memory
Controller
User
Logic
PLL
FPGA
DLL
- ALTMEMPHY IP User Guide 1
- Contents 3
- Chapter 7. Latency 5
- Chapter 8. Timing Diagrams 5
- 1. About This IP 7
- Release Information 8
- Device Family Support 8
- Features 9
- Unsupported Features 10
- MegaCore Verification 10
- Resource Utilization 11
- System Requirements 12
- Installation and Licensing 13
- 1–8 Chapter 1: About This IP 14
- 2. Getting Started 15
- SOPC Builder Flow 16
- Qsys Flow 18
- Completing the Qsys System 19
- Specifying Parameters 20
- HardCopy Guidelines 21
- Generated Files 22
- 3. Parameter Settings 27
- Memory Settings 28
- ALTMEMPHY Parameter Settings 29
- Note to Table 3–3: 32
- Note to Table 3–5: 34
- PHY Settings 36
- Board Settings 38
- ■ Memory Settings 39
- ■ PHY Settings 39
- ■ Board Settings 39
- ■ Controller Settings 39
- Controller Settings 40
- 4. Compiling and Simulating 43
- Compiling the Design 44
- Simulating the Design 46
- Block Description 48
- Calibration 49
- Address and Command Datapath 49
- ), or the inverted 50
- Clock and Reset Management 51
- Notes to Table 5–4: 54
- Note to Table 5–2: 57
- Cyclone III Devices 59
- Read Datapath 66
- Note to Figure 5–6: 68
- Note to Figure 5–8: 70
- Devices 71
- GX Devices 72
- ALTMEMPHY Signals 73
- Notes to Table 5–5: 74
- Note to Table 5–5: 77
- Notes to Table 5–7: 79
- PHY-to-Controller Interfaces 80
- Altera Device 81
- -- a --b 82
- Figure 5–15. Full-Rate Reads 83
- Figure 5–16. Half-Rate Reads 83
- Notes to Figure 5–17: 85
- Notes to Figure 5–18: 86
- Notes to Figure 5–19: 87
- Notes to Figure 5–20: 88
- Preliminary Steps 89
- Design Considerations 89
- Clocks and Resets 89
- Using a Custom Controller 90
- Partial Write Operations 92
- 6. Functional Description— 95
- Avalon-ST Input Interface 96
- Command Generator 96
- Timing Bank Pool 96
- Arbitration Rules 97
- CSR Interface 98
- Data Reordering 98
- Pre-emptive Bank Management 98
- Quasi-1T and Quasi-2T 98
- User Autoprecharge Commands 98
- User-Controlled Self-Refresh 99
- DDR2 SDRAM 100
- Partial Writes 101
- Partial Bursts 102
- External Interfaces 103
- Memory Side-Band Signals 104
- Top-Level Signals Description 105
- ■ Full rate controllers 107
- ■ Half rate controllers 107
- Sequence of Operations 111
- Read Command 112
- Read-Modify-Write Command 112
- Example Top-Level File 113
- Example Driver 114
- Register Maps 116
- Controller Register Map 118
- 7. Latency 123
- 7–2 Chapter 7: Latency 124
- Note to Table 7–2: 125
- SDRAM values 126
- Handbook 127
- 7–6 Chapter 7: Latency 128
- 8. Timing Diagrams 129
- Half-Rate Read 130
- Half-Rate Write 132
- Full-Rate Read 134
- Full-Rate Write 136
- Additional Information 139
- Typographic Conventions 140
Prodotti e manuali riguardandi Strumenti di misura Altera DDR SDRAM High-Performance Controllers and ALTMEMP
Strumenti di misura Altera Nios II Embedded Evaluation Kit Cyclone III Editio Manuale Utente
(3 pagine)
(3 pagine)
Strumenti di misura Altera Nios II Embedded Evaluation Kit Cyclone III Editio Manuale Utente
(80 pagine)
(80 pagine)
Strumenti di misura Altera SCFIFO Manuale Utente
(28 pagine)
(28 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale