Altera UG-01080 Guida Utente Pagina 533
- Pagina / 702
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Offset Bits R/W Register Name Description
0x3 [4:0] RW Pre-emphasis second post-tap
The following encodings are defined:
• 5’b00000 and 5’b10000: 0
• 5’b00001–5’b01111: -15 to -1
• 5’b10001–5b’11111: 1 to 15
0x10 [2:0] RW RX equalization DC gain
(17)
The following encodings are defined:
• 3’b000–3’b011:0–3
• 3'b100-3'b110:4
• 3'b111:Reserved
0x11 [3:0] RW RX equalization control
The following encodings are defined:
• 4’b0000–4’b1111: 0–15
0x20 [0] WO Pre-CDR Reverse Serial Loopback Writing a 1 to this bit enables reverse
serial loopback. Writing a 0 disables
pre-CDR reverse serial loopback.
0x21 [0] WO Post-CDR Reverse Serial Loopback Writing a 1 to this bit enables post-
CDR reverse serial loopback. Writing
a 0 disables post-CDR reverse serial
loopback.
Refer to Changing Transceiver Settings Using Register-Based Reconfiguration and Changing Transceiver
Settings Using Streamer-Based Reconfiguration for the procedures you can use to update PMA settings.
Related Information
• Arria V Device Datasheet
• Cyclone V Device Datasheet
• Stratix V Device Datasheet
• Application Note 645: Dynamic Reconfiguration of PMA Controls in Stratix V Devices
Transceiver Reconfiguration Controller EyeQ Registers
EyeQ is a debug and diagnostic tool that analyzes the incoming data, including the receiver’s gain, noise
level, and jitter after the receive buffer. EyeQ is only available for Stratix V and Arria V GZ devices.
(17)
There are two possible methods to modify the RX linear equalization settings:
• Using the reconfiguration controller (offset 0x11)
• Using the QSF assignments
Different values are used for each method. The settings for using the reconfiguration controller range from 0
to 15 and the settings for using the QSF assignments are from 1 to 16. For example, setting 0 in the
transceiver reconfiguration controller corresponds to setting 1 for the QSF assignments and so forth.
16-16
Transceiver Reconfiguration Controller EyeQ Registers
UG-01080
2015.01.19
Altera Corporation
Transceiver Reconfiguration Controller IP Core Overview
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Altera Corporation 10
- Native Transceiver PHYs 12
- Transceiver PHY Modules 15
- Resetting the Transceiver PHY 16
- File Name Description 18
- Unsupported Features 20
- Getting Started Overview 21
- Design Flows 22
- Specifying Parameters 23
- Simulate the IP Core 24
- 10GBASE-R PHY IP Core 25
- Arria V GT 10GBASE-R 27
- Transceiver Protocol 28
- General Option Parameters 33
- 10GBASE-R PHY Interfaces 37
- 10GBASE-R PHY Data Interfaces 38
- Reset Control and Power Down 46
- Signal Name Directio 53
- 1588 Delay Requirements 54
- 10GBASE-R Parameters 63
- Reconfig 67
- 10BASE-KR PHY Interfaces 75
- Daisy-Chain Interface Signals 83
- Bit R/W Name Description 100
- PMA Registers 103
- PCS Registers 104
- Creating a 10GBASE-KR Design 105
- Editing a 10GBASE-KR MIF File 106
- Send Feedback 107
- Design Example 108
- SDC Timing Constraints 109
- Acronyms 109
- UG-01080 110
- Subscribe 110
- Related Information 111
- Item Description 111
- Device Family Support 112
- 1GbE Parameters 113
- Speed Detection Parameters 114
- PHY Analog Parameters 115
- 1G/10GbE PHY Interfaces 116
- 2015.01.19 117
- 1G/10GbE PHY Data Interfaces 118
- Serial Data Interface 121
- Register Interface Signals 123
- Addr Bit R/W Name Description 124
- 1G/10 GbE GMII PCS Registers 127
- Cntl & 131
- Editing a 1G/10GbE MIF File 132
- Creating a 1G/10GbE Design 133
- Simulation Support 139
- TimeQuest Timing Constraints 139
- WAN Wide Area Network 140
- XAUI PHY IP Core 141
- XAUI PHY Release Information 142
- Stratix V Devices 143
- Parameterizing the XAUI PHY 143
- XAUI PHY General Parameters 144
- Name Value Description 145
- XAUI PHY Analog Parameters 146
- Advanced Options Parameters 148
- XAUI PHY Configurations 149
- XAUI PHY Ports 150
- XAUI PHY Data Interfaces 151
- SDR XGMII TX Interface 152
- SDR XGMII RX Interface 153
- XAUI Hard IP Core 154
- Hard PCS 154
- Soft PCS 154
- Name Direction Description 157
- Interlaken PHY IP Core 168
- Parameter Value Description 170
- Interlaken PHY Interfaces 173
- Interlaken PHY PLL Interface 181
- Preset C 198
- PHY for PCIe (PIPE) Clocks 201
- Signal Name 202
- Direction Signal Name 202
- PHY IP Core for PCI Express 204
- Hard PCS and PMA 204
- Phase 2 (Optional) 210
- Phase 3 (Optional) 211
- Custom PHY IP Core 214
- Parameterizing the Custom PHY 216
- Word Alignment Parameters 220
- Rate Match FIFO Parameters 222
- Byte Order Parameters 224
- Analog Parameters 229
- Presets for Ethernet 229
- Interfaces 232
- Configuration Bus Used Bits 234
- Clock Interface 236
- Optional Status Interface 237
- Custom PHY PCS and PMA 241
- Custom PHY IP Core Registers 242
- Reset Controls –Manual Mode 243
- Custom PCS 245
- Dynamic Reconfiguration 246
- Low Latency PHY IP Core 248
- General Options Parameters 251
- Additional Options Parameters 254
- TX PLL (0–3) 258
- (Refer to 258
- Channel Interface 259
- Low Latency PHY Interfaces 260
- PMA and Light-Weight PCS 264
- Data Rate (Mbps) 270
- TX_tc lock_output 273
- PDI O >R X_ deser 273
- Serial Data Rate (Mbps) 277
- Single-Width Double-Width 277
- 8-Bit 16-Bit 16-Bit 32-Bit 277
- TX Data Word Description 285
- RX Data Word Description 286
- Deterministic PHY IP Core 291
- Parameter Presets 301
- Name Range Description 302
- Parameter Range Description 304
- PATTERN POLYNOMIAL 323
- PCS-PMA Width 323
- 8-Bit 10-Bit 16-Bit 20-Bit 323
- 10G PCS Pattern Generators 340
- Native PHY Common Interfaces 345
- Standard PCS Interface Ports 351
- Name Dir Synchronous to 353
- Description 353
- 10G PCS Interface 356
- 10G PCS Interface Ports 357
- ×6/×N Bonded Clocking 367
- Transceiver Bank 368
- Slew Rate Settings 374
- General Parameters 378
- PMA Parameters 379
- TX PMA Parameters 380
- TX PLL Parameters 381
- RX PMA Parameters 383
- Standard PCS Parameters 385
- Phase Compensation FIFO 387
- Rate Match FIFO 390
- Overview 484
- Cyclone Device Family Support 485
- Altera V-Series FPGA 520
- Utilization 522
- Embedded 529
- Controller 529
- Offset Cancellation 530
- Duty Cycle Calibration 530
- EyeQ Usage Example 536
- Turning on Triggered DFE Mode 540
- Channel Reconfiguration 550
- PLL Reconfiguration 550
- MIF Generation 554
- MIF Format 555
- Reduced MIF Creation 559
- Register-Based Read 560
- Direct Write Reconfiguration 561
- Reconfiguration 565
- Loopback Modes 575
- Transceiver 576
- Transceiver PHY Instance 579
- Transceiver PHY 579
- Reset Controller 579
- Transceiver PLL Parameters 592
- Transceiver PLL Signals 593
- XCVR_IO_PIN_TERMINATION 596
- XCVR_REFCLK_PIN_TERMINATION 597
- XCVR_TX_SLEW_RATE_CTRL 597
- XCVR_VCCR_ VCCT_VOLTAGE 598
- CDR_BANDWIDTH_PRESET 598
- PLL_BANDWIDTH_PRESET 599
- XCVR_RX_DC_GAIN 599
- XCVR_ANALOG_SETTINGS_PROTOCOL 599
- XCVR_RX_COMMON_MODE_VOLTAGE 600
- XCVR_RX_SD_ENABLE 601
- XCVR_RX_SD_OFF 601
- XCVR_RX_SD_ON 602
- XCVR_RX_SD_THRESHOLD 602
- XCVR_TX_COMMON_MODE_VOLTAGE 603
- XCVR_TX_PRE_EMP_1ST_POST_TAP 603
- XCVR_TX_RX_DET_ENABLE 603
- XCVR_TX_RX_DET_MODE 604
- XCVR_TX_VOD 604
- XCVR_TX_VOD_PRE_EMP_CTRL_SRC 604
- XCVR_RX_BYPASS_EQ_STAGES_234 606
- XCVR_VCCA_VOLTAGE 607
- XCVR_VCCR_VCCT_VOLTAGE 608
- XCVR_TX_PRE_EMP_PRE_TAP_USER 615
- XCVR_TX_PRE_EMP_2ND_POST_TAP 616
- XCVR_TX_PRE_EMP_INV_2ND_TAP 616
- XCVR_TX_PRE_EMP_INV_PRE_TAP 617
- XCVR_TX_PRE_EMP_PRE_TAP 617
- XCVR_TX_RX_DET_OUTPUT_SEL 618
- XCVR_GT_IO_PIN_TERMINATION 628
- XCVR_GT_RX_DC_GAIN 635
- XCVR_GT_RX_CTLE 636
- XCVR_GT_TX_PRE_EMP_ PRE_TAP 638
- XCVR_GT_TX_VOD_MAIN_TAP 638
- Transceivers 648
- 2013.12.20 650
- Stratix IV GX Devices 651
- Parameter Name 653
- Comments 653
- Custom PHY Width 659
- Chapter Document 661
- Changes Made 661
- Date Document 676
- How to Contact Altera 702
Prodotti e manuali riguardandi Software Altera UG-01080
Software Altera PHY IP Core Guida Utente
(230 pagine)
(230 pagine)
Software Altera UG-01080 Guida Utente
(120 pagine)
(120 pagine)
Software Altera DE2-115 Guida Utente
(107 pagine)
(107 pagine)
Software Altera UG-01080 Guida Utente
(484 pagine)
(484 pagine)
Samsung RT34GKPN manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Samsung RT34GKPN.
Nous fournissons des manuels en pdf 1 Samsung RT34GKPN à télécharger gratuitement par type de document : Manuel de l'utilisateur
Samsung RT34GKPN Manuel de l'utilisateur (16 pages)
marque: Samsung | Catégorie: No info | Taille: 20.67 MB |
Table des matières
Plus de produits et de manuels pour Non Samsung
| Modèles | Type de document |
|---|---|
| EO-RG920B |
Manuel de l'utilisateur
 
Samsung EO-RG920B Kasutusjuhend,
754 pages
|
| SAMSUNG PL100 |
Manuel de l'utilisateur
Samsung SAMSUNG PL101 ユーザーマニュアル,
98 pages
|
| UA32FH4003R |
Manuel de l'utilisateur
Samsung UA32FH4003R دليل الاستخدام,
2 pages
|
| RL39THCTS |
Manuel de l'utilisateur
Samsung RL43THCMG Manual de utilizare,
28 pages
|
| LW15M23C |
Manuel de l'utilisateur
Samsung LW15M23C Benutzerhandbuch,
55 pages
|
| SCH-B179P |
Manuel de l'utilisateur
Samsung SCH-B179P ユーザーマニュアル,
2 pages
|
| UE40KU6100W |
Manuel de l'utilisateur
 
Samsung UE49KU6172U User Manual,
228 pages
|
| WF7602SUV |
Manuel de l'utilisateur
Samsung WF7602SUV Manual de Usuario,
24 pages
|
| MW81W-S/XEH |
Manuel de l'utilisateur
Samsung MW81W-S/XEH User manual,
8 pages
|
| ARN-CP62B | Manuel de l'utilisateur Samsung ARX-CP62 사용자 설명서, 28 pages |
| SM-J500H | Manuel de l'utilisateur Samsung Galaxy J5 User Manual , 103 pages |
| YP-U4JAB |
Manuel de l'utilisateur
Samsung YP-U4JQB User guide,
85 pages
|
| SH09APGDX |
Manuel de l'utilisateur
Samsung SH24AP6DX User Manual,
26 pages
|
| AQ12FEX |
Manuel de l'utilisateur
Samsung AQ12FEX Manual de usuario,
22 pages
|
| YP-P2CB |
Manuel de l'utilisateur
Samsung YP-P2CB คู่มือการใช้งาน,
141 pages
|
| UA43J5100AR |
Manuel de l'utilisateur
Samsung 55'' Full HD Flat TV J5100 Series 5 دليل الاستخدام,
2 pages
|
| HT-SB1R |
Manuel de l'utilisateur
Samsung HT-SB1R คู่มือการใช้,
20 pages
|
| RT411GBEW |
Manuel de l'utilisateur
Samsung RT411GBEW User Manual,
24 pages
|
| PS60F5000AR |
Manuel de l'utilisateur
Samsung PS51F4500AR Quick start guide,
19 pages
|
| YP-G1CW |
Manuel de l'utilisateur
Samsung YP-G1CW ユーザーマニュアル [ja] [zh] ,
103 pages
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale