Altera UG-01080 Guida Utente Pagina 334
- Pagina / 702
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Parameter Range Description
teng_tx_framgen_burst_enable On/Off When you turn this option On, the
frame generator burst functionality is
enabled.
Enable tx_10g_frame port On/Off When you turn this option On, the 10G
PCS includes the tx_10g_frame output
port. When asserted, tx_10g_frame
indicates the beginning of a new
metaframe inside the frame generator.
Enable tx_10g_frame_diag_status port On/Off When you turn this option On, the 10G
PCS includes the tx_10g_frame_diag_
status 2-bit input port. This port
contains the lane Status Message from
the framing layer Diagnostic Word,
bits[33:32]. This message is inserted into
the next Diagnostic Word generated by
the frame generation block. The
message must be held static for 5 cycles
before and 5 cycles after the tx_frame
pulse.
Enable tx_10g_frame_burst_en port On/Off When you turn this option On, the 10G
PCS includes the tx_10g_frame_burst_
en input port. This port controls frame
generator data reads from the TX FIFO.
The value of this signal is latched once at
the beginning of each Metaframe. It
controls whether data is read from the
TX FIFO or SKIP Words are inserted
for the current Metaframe. It must be
held static for 5 cycles before and 5
cycles after the tx_frame pulse. When
tx_10g_frame_burst_en is 0, the frame
generator does not read data from the
TX FIFO for current Metaframe. It
insert SKIPs. When tx_10g_frame_
burst_en is 1, the frame generator reads
data from the TX FIFO for current
Metaframe.
Interlaken Frame Synchronizer
The Interlaken frame synchronizer block achieves lock by looking for four synchronization words in
consecutive metaframes. After synchronization, the frame synchronizer monitors the scrambler word in
the metaframe and deasserts the lock signal after three consecutive mismatches and starts the synchroni‐
zation process again. Lock status is available to the FPGA fabric. The following table describes the
Interlaken frame synchronizer parameters.
12-36
10G PCS Parameters for Stratix V Native PHY
UG-01080
2015.01.19
Altera Corporation
Stratix V Transceiver Native PHY IP Core
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Altera Corporation 10
- Native Transceiver PHYs 12
- Transceiver PHY Modules 15
- Resetting the Transceiver PHY 16
- File Name Description 18
- Unsupported Features 20
- Getting Started Overview 21
- Design Flows 22
- Specifying Parameters 23
- Simulate the IP Core 24
- 10GBASE-R PHY IP Core 25
- Arria V GT 10GBASE-R 27
- Transceiver Protocol 28
- General Option Parameters 33
- 10GBASE-R PHY Interfaces 37
- 10GBASE-R PHY Data Interfaces 38
- Reset Control and Power Down 46
- Signal Name Directio 53
- 1588 Delay Requirements 54
- 10GBASE-R Parameters 63
- Reconfig 67
- 10BASE-KR PHY Interfaces 75
- Daisy-Chain Interface Signals 83
- Bit R/W Name Description 100
- PMA Registers 103
- PCS Registers 104
- Creating a 10GBASE-KR Design 105
- Editing a 10GBASE-KR MIF File 106
- Send Feedback 107
- Design Example 108
- SDC Timing Constraints 109
- Acronyms 109
- UG-01080 110
- Subscribe 110
- Related Information 111
- Item Description 111
- Device Family Support 112
- 1GbE Parameters 113
- Speed Detection Parameters 114
- PHY Analog Parameters 115
- 1G/10GbE PHY Interfaces 116
- 2015.01.19 117
- 1G/10GbE PHY Data Interfaces 118
- Serial Data Interface 121
- Register Interface Signals 123
- Addr Bit R/W Name Description 124
- 1G/10 GbE GMII PCS Registers 127
- Cntl & 131
- Editing a 1G/10GbE MIF File 132
- Creating a 1G/10GbE Design 133
- Simulation Support 139
- TimeQuest Timing Constraints 139
- WAN Wide Area Network 140
- XAUI PHY IP Core 141
- XAUI PHY Release Information 142
- Stratix V Devices 143
- Parameterizing the XAUI PHY 143
- XAUI PHY General Parameters 144
- Name Value Description 145
- XAUI PHY Analog Parameters 146
- Advanced Options Parameters 148
- XAUI PHY Configurations 149
- XAUI PHY Ports 150
- XAUI PHY Data Interfaces 151
- SDR XGMII TX Interface 152
- SDR XGMII RX Interface 153
- XAUI Hard IP Core 154
- Hard PCS 154
- Soft PCS 154
- Name Direction Description 157
- Interlaken PHY IP Core 168
- Parameter Value Description 170
- Interlaken PHY Interfaces 173
- Interlaken PHY PLL Interface 181
- Preset C 198
- PHY for PCIe (PIPE) Clocks 201
- Signal Name 202
- Direction Signal Name 202
- PHY IP Core for PCI Express 204
- Hard PCS and PMA 204
- Phase 2 (Optional) 210
- Phase 3 (Optional) 211
- Custom PHY IP Core 214
- Parameterizing the Custom PHY 216
- Word Alignment Parameters 220
- Rate Match FIFO Parameters 222
- Byte Order Parameters 224
- Analog Parameters 229
- Presets for Ethernet 229
- Interfaces 232
- Configuration Bus Used Bits 234
- Clock Interface 236
- Optional Status Interface 237
- Custom PHY PCS and PMA 241
- Custom PHY IP Core Registers 242
- Reset Controls –Manual Mode 243
- Custom PCS 245
- Dynamic Reconfiguration 246
- Low Latency PHY IP Core 248
- General Options Parameters 251
- Additional Options Parameters 254
- TX PLL (0–3) 258
- (Refer to 258
- Channel Interface 259
- Low Latency PHY Interfaces 260
- PMA and Light-Weight PCS 264
- Data Rate (Mbps) 270
- TX_tc lock_output 273
- PDI O >R X_ deser 273
- Serial Data Rate (Mbps) 277
- Single-Width Double-Width 277
- 8-Bit 16-Bit 16-Bit 32-Bit 277
- TX Data Word Description 285
- RX Data Word Description 286
- Deterministic PHY IP Core 291
- Parameter Presets 301
- Name Range Description 302
- Parameter Range Description 304
- PATTERN POLYNOMIAL 323
- PCS-PMA Width 323
- 8-Bit 10-Bit 16-Bit 20-Bit 323
- 10G PCS Pattern Generators 340
- Native PHY Common Interfaces 345
- Standard PCS Interface Ports 351
- Name Dir Synchronous to 353
- Description 353
- 10G PCS Interface 356
- 10G PCS Interface Ports 357
- ×6/×N Bonded Clocking 367
- Transceiver Bank 368
- Slew Rate Settings 374
- General Parameters 378
- PMA Parameters 379
- TX PMA Parameters 380
- TX PLL Parameters 381
- RX PMA Parameters 383
- Standard PCS Parameters 385
- Phase Compensation FIFO 387
- Rate Match FIFO 390
- Overview 484
- Cyclone Device Family Support 485
- Altera V-Series FPGA 520
- Utilization 522
- Embedded 529
- Controller 529
- Offset Cancellation 530
- Duty Cycle Calibration 530
- EyeQ Usage Example 536
- Turning on Triggered DFE Mode 540
- Channel Reconfiguration 550
- PLL Reconfiguration 550
- MIF Generation 554
- MIF Format 555
- Reduced MIF Creation 559
- Register-Based Read 560
- Direct Write Reconfiguration 561
- Reconfiguration 565
- Loopback Modes 575
- Transceiver 576
- Transceiver PHY Instance 579
- Transceiver PHY 579
- Reset Controller 579
- Transceiver PLL Parameters 592
- Transceiver PLL Signals 593
- XCVR_IO_PIN_TERMINATION 596
- XCVR_REFCLK_PIN_TERMINATION 597
- XCVR_TX_SLEW_RATE_CTRL 597
- XCVR_VCCR_ VCCT_VOLTAGE 598
- CDR_BANDWIDTH_PRESET 598
- PLL_BANDWIDTH_PRESET 599
- XCVR_RX_DC_GAIN 599
- XCVR_ANALOG_SETTINGS_PROTOCOL 599
- XCVR_RX_COMMON_MODE_VOLTAGE 600
- XCVR_RX_SD_ENABLE 601
- XCVR_RX_SD_OFF 601
- XCVR_RX_SD_ON 602
- XCVR_RX_SD_THRESHOLD 602
- XCVR_TX_COMMON_MODE_VOLTAGE 603
- XCVR_TX_PRE_EMP_1ST_POST_TAP 603
- XCVR_TX_RX_DET_ENABLE 603
- XCVR_TX_RX_DET_MODE 604
- XCVR_TX_VOD 604
- XCVR_TX_VOD_PRE_EMP_CTRL_SRC 604
- XCVR_RX_BYPASS_EQ_STAGES_234 606
- XCVR_VCCA_VOLTAGE 607
- XCVR_VCCR_VCCT_VOLTAGE 608
- XCVR_TX_PRE_EMP_PRE_TAP_USER 615
- XCVR_TX_PRE_EMP_2ND_POST_TAP 616
- XCVR_TX_PRE_EMP_INV_2ND_TAP 616
- XCVR_TX_PRE_EMP_INV_PRE_TAP 617
- XCVR_TX_PRE_EMP_PRE_TAP 617
- XCVR_TX_RX_DET_OUTPUT_SEL 618
- XCVR_GT_IO_PIN_TERMINATION 628
- XCVR_GT_RX_DC_GAIN 635
- XCVR_GT_RX_CTLE 636
- XCVR_GT_TX_PRE_EMP_ PRE_TAP 638
- XCVR_GT_TX_VOD_MAIN_TAP 638
- Transceivers 648
- 2013.12.20 650
- Stratix IV GX Devices 651
- Parameter Name 653
- Comments 653
- Custom PHY Width 659
- Chapter Document 661
- Changes Made 661
- Date Document 676
- How to Contact Altera 702
Prodotti e manuali riguardandi Software Altera UG-01080
Software Altera PHY IP Core Guida Utente
(230 pagine)
(230 pagine)
Software Altera UG-01080 Guida Utente
(120 pagine)
(120 pagine)
Software Altera DE2-115 Guida Utente
(107 pagine)
(107 pagine)
Software Altera UG-01080 Guida Utente
(484 pagine)
(484 pagine)
ShelterLogic 72874.0 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non ShelterLogic 72874.0.
Nous fournissons des manuels en pdf 1 ShelterLogic 72874.0 à télécharger gratuitement par type de document : Manuel d'instructions
Shelterlogic 72874.0 Manuel d'instructions (9 pages)
marque: Shelterlogic | Catégorie: No info | Taille: 0.87 MB |
Table des matières
Plus de produits et de manuels pour Non ShelterLogic
| Modèles | Type de document |
|---|---|
| 25712 |
Manuel d'instructions
 
ShelterLogic 25712 Instructions / Assembly,
1 pages
|
| 90478 |
Manuel d'utilisation et d'entretien
ShelterLogic 90478 Use and Care Manual,
1 pages
|
| 90490 |
Manuel d'utilisation et d'entretien
ShelterLogic 90490 Use and Care Manual,
1 pages
|
| 70593 |
Manuel d'instructions
ShelterLogic 70593 Instructions / Assembly,
16 pages
|
| 70560 |
Manuel d'utilisation et d'entretien
ShelterLogic 70560 Use and Care Manual,
1 pages
|
| 62693.0 |
Manuel d'instructions
ShelterLogic 62693.0 Instructions / Assembly,
27 pages
|
| 73432.0 |
Manuel d'instructions
ShelterLogic 73432.0 Instructions / Assembly,
6 pages
|
| 72814 |
Manuel d'utilisation et d'entretien
ShelterLogic 72814 Use and Care Manual,
1 pages
|
| 10077.0 |
Manuel d'instructions
ShelterLogic 10077.0 Instructions / Assembly,
9 pages
|
| 95360 |
Manuel d'utilisation et d'entretien
ShelterLogic 95360 Use and Care Manual,
1 pages
|
| 62807 |
Manuel d'utilisation et d'entretien
ShelterLogic 62807 Use and Care Manual,
1 pages
|
| 82144 |
Manuel d'utilisation et d'entretien
ShelterLogic 82144 Use and Care Manual,
1 pages
|
| 70652 |
Manuel d'utilisation et d'entretien
ShelterLogic 70652 Use and Care Manual,
1 pages
|
| 90460 |
Manuel d'utilisation et d'entretien
ShelterLogic 90460 Use and Care Manual,
1 pages
|
| 10471.0 |
Manuel d'utilisation et d'entretien
ShelterLogic 10471.0 Use and Care Manual,
15 pages
|
| 77824.0 |
Manuel d'instructions
ShelterLogic 77824.0 Instructions / Assembly,
18 pages
|
| 90396 |
Manuel d'instructions
ShelterLogic 90396 Instructions / Assembly,
27 pages
|
| 62807 |
Manuel d'instructions
ShelterLogic 62807 Instructions / Assembly,
36 pages
|
| 71814 |
Manuel d'utilisation et d'entretien
ShelterLogic 71814 Use and Care Manual,
1 pages
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale