Altera CPRI IP Core Manuale Utente Pagina 117
- Pagina / 220
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
December 2013 Altera Corporation CPRI MegaCore Function
User Guide
7. Software Interface
The Altera CPRI IP core supports the following sets of registers that control the CPRI
IP core or query its status:
■ CPRI Protocol Interface Registers
■ MAP Interface and AUX Interface Configuration Registers
■ Ethernet Registers
■ HDLC Registers
All of the registers are 32 bits wide and their addresses are shown as hexadecimal
values. The registers can be accessed only on a 32-bit (4-byte) basis. The addressing for
the registers therefore increments by units of 4.
1 Reserved fields are labelled in the register tables. These fields are reserved for future
use and your design should not write to or rely on a specific value being found in any
reserved field or bit.
A remote device can access these registers only by issuing read and write operations
through the CPU interface.
Table 7–1 lists the access codes that describe the type of register bits.
Table 7–2 lists the CPRI IP core register address ranges.
Table 7–1. Register Access Codes
Code Description
RC Read to clear
RO Read-only
RW Read/write
UR0 Unused bits/read as 0
WO Write-only; read as 0
Table 7–2. CPRI IP Core Register Address Ranges
Address Range Interface
0x00–0x68 CPRI Protocol Interface Registers
0x100–0x1A4 MAP Interface and AUX Interface Configuration Registers
0xF4–0x1FC Reserved
0x200–0x24C Ethernet Registers
0x250–0x2FC Reserved
0x300–0x334 HDLC Registers
- User Guide 1
- CPRI MegaCore Function 1
- Contents 3
- Chapter 5. Testing Features 4
- ContentsContents v 5
- General Description 8
- CPRI IP Core Features 10
- Device Family Support 11
- MegaCore Verification 12
- Release Information 14
- Installation and Licensing 15
- OpenCore Plus Evaluation 16
- 2. Getting Started 17
- Specifying Parameters 18
- Simulation Files 19
- Simulating the Design 20
- Supporting the Transceivers 21
- Specifying Constraints 21
- 3. Parameter Settings 25
- Operation Mode Parameter 26
- Line Rate Parameter 26
- Enable Autorate Negotiation 27
- Rx Elastic Buffer Depth 27
- Include MAC Block 28
- Include HDLC Block 29
- Mapping Mode 29
- Application Layer Parameters 30
- Words” on page 4–42 32
- 4. Functional Description 33
- Architecture Overview 34
- CPRI IP Core Clocks 35
- Clocking Structure 36
- Notes to Table 4–2: 42
- Reset Requirements 43
- MegaCore 44
- Function 44
- MAP Interface Mapping Modes 45
- Basic AxC Mapping Mode 46
- MAP Interface 47
- Note to Table 4–5: 49
- Note to Table 4–6: 49
- Advanced AxC Mapping Modes 50
- MAP Receiver Interface 50
- Notes to Table 4–7: 51
- MAP Receiver in FIFO Mode 52
- MAP Transmitter Interface 56
- Notes to Table 4–10: 57
- MAP Transmitter in FIFO Mode 58
- Auxiliary Interface 62
- AUX Receiver Module 63
- Avalon-ST 32-bit interface 64
- AUX Transmitter Module 66
- Note to Figure 4–19: 67
- MII Transmitter 70
- MII Receiver 71
- CPU Interface 73
- Control Word Order 78
- Transmitting Ethernet Traffic 80
- Receiving Ethernet Traffic 81
- Accessing the HDLC Channel 82
- Note to Table 4–15: 83
- Features 84
- Physical Layer Architecture 84
- Receiver 85
- High-Speed Transceiver 86
- Rx Elastic Buffer 86
- Descrambling 87
- Frame Synchronization 87
- Alarm Indications 88
- Reset Control Word 89
- Transmitter 90
- Scrambling 91
- Tx Elastic Buffer 91
- External Loopback 93
- CPRI IP Core 93
- Internal Reverse Loopback 94
- Physical Layer Loopback Mode 94
- (1) (2) (3) 96
- MAP Receiver Signals 99
- 6–2 Chapter 6: Signals 100
- MAP Interface Signals 100
- MAP Transmitter Signals 101
- 6–4 Chapter 6: Signals 102
- Auxiliary Interface Signals 103
- AUX Receiver Signals 104
- AUX Transmitter Signals 105
- 6–8 Chapter 6: Signals 106
- Extended Rx Status Signals 107
- CPRI MII Receiver Signals 108
- CPRI MII Transmitter Signals 108
- CPU Interface Signals 109
- CPRI Data Signals 110
- Layer 1 Error Signal 111
- Autorate Negotiation Signals 111
- 6–14 Chapter 6: Signals 112
- Physical Layer Signals 112
- Transceiver Signals 113
- 6–16 Chapter 6: Signals 114
- Note to Table 6–14: 115
- 6–18 Chapter 6: Signals 116
- 7. Software Interface 117
- Note to Table 7–5: 119
- CPRI_HW_RESET 123
- register, refer to “Reset 123
- Requirements” on page 4–11 123
- Note to Table 7–13: 124
- Note to Table 7–16: 125
- Note to Table 7–17: 126
- Note to Table 7–20: 126
- Notes to Table 7–21: 127
- Notes to Table 7–28: 130
- Notes to Table 7–29: 130
- Note to Table 7–32: 133
- Note to Table 7–33: 133
- Note to Table 7–34: 133
- Note to Table 7–35: 134
- Note to Table 7–36: 134
- Notes to Table 7–37: 135
- Notes to Table 7–38: 135
- Notes to Table 7–39: 136
- Notes to Table 7–40: 136
- Note to Table 7–45: 137
- Ethernet Registers 138
- HDLC Registers 143
- Note to Figure 8–1: 150
- Test Sequence 151
- Running the Testbench 153
- A. Initialization Sequence 155
- Negotiation 157
- Notes for Figure B–1: 158
- Running Autorate Negotiation 159
- Notes to Table C–3: 167
- D. Advanced AxC Mapping Modes 173
- Fifteen-Bit Width Mode 175
- Sixteen-Bit Width Mode 176
- Note to Figure D–2: 177
- Delay Requirements 179
- RE SlaveREC Master 180
- Rx Path Delay 181
- Most CPRI IP Core Variations 181
- Single-Hop Delay Measurement 182
- Notes to Table E–1: 183
- Notes to Table E–2: 184
- Notes to Table E–3: 186
- Arria V GT 9.8 Gbps 188
- Notes to Table E–4: 189
- Tx Path Delay 190
- Note to Table E–6: 192
- T_txv_TX 194
- in Figure E–1 on page E–2 194
- Round-Trip Delay 196
- Round-Trip Cable Delay 196
- Families 202
- Round-Trip Delay Calculation 205
- Multi-Hop Delay Measurement 206
- Additional Information 213
- Document Revision History 214
- How to Contact Altera 218
- Typographic Conventions 218
Prodotti e manuali riguardandi Strumenti di misura Altera CPRI IP Core
(38 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale