Altera PHY IP Core Guida Utente Pagina 43
- Pagina / 626
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Protocol Transceiver IP PCS Support Transceiver
Configuration
Rule
(15)
Protocol Preset
(16)
100GBASE-R via CAUI Native PHY IP Enhanced Basic (Enhanced
PCS)
Low Latency Enhanced
PCS
(22)
100GBASE-R via CAUI
with FEC
Native PHY IP Enhanced Basic w/KR FEC User created
XAUI XAUI PHY IP Soft PCS Not applicable Not applicable
SPAUI Native PHY IP Standard and
Enhanced
Basic/Custom
(Standard PCS)
Basic (Enhanced
PCS)
User created
DDR XAUI Native PHY IP Standard and
Enhanced
Basic/Custom
(Standard PCS)
Basic (Enhanced
PCS)
User created
Interlaken (CEI-6G/
11G)
(20)
Native PHY IP Enhanced Interlaken
Interlaken 10x12.5Gbps
Interlaken 6x10.3Gbps
Interlaken 1x6.25Gbps
OTU-4 (100G) via OTL4.4/
CEI-25G/28G VSR/SR
Native PHY IP
Enhanced PCS
(low latency
mode)
PCS Direct
Basic (Enhanced
PCS) / PCS
Direct
Low Latency GT
(23)
(15)
For more information about Transceiver Configuration Rules, refer to Using the Arria 10 Transceiver
Native PHY IP Core on page 2-17.
(16)
For more information about Protocol Presets, refer to Using the Arria 10 Transceiver Native PHY IP Core
on page 2-17.
(17)
Hard IP for PCI Express is also available as a separate IP core.
(18)
The 1G/10GbE and 10GBASE-KR PHY IP core includes the necessary soft IP for link training, auto speed
negotiation, and sequencer functions.
(19)
Needs a user created IP for link training, auto speed negotiation, and sequencer functions.
(20)
A Transmit PCS soft bonding logic required for multi-lane bonding configuration and a Receive PCS multi-
lane deskew control logic is provided in the design example.
(21)
To implement 40GBASE-R/100GBASE-R using the Low Latency Enhanced PCS preset, change the number
of data channels to four and select appropriate PCS- FPGA Fabric and PCS-PMA width.
(22)
To implement 100GBASE-R via CAUI using the Low Latency Enhanced PCS preset, change the number of
data channels to 10 and select appropriate PCS-FPGA Fabric and PCS-PMA width.
(23)
Low Latency GT protocol preset requires some modification to implement OTU-4 (100G) via OTL4.4/CEI-
28G-VSR.
2-12
Arria 10 Transceiver Protocols and PHY IP Support
UG-01143
2015.05.11
Altera Corporation
Implementing Protocols in Arria 10 Transceivers
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Device Transceiver Layout 9
- UG-01143 10
- 2015.05.11 10
- Transceiver Bank Architecture 22
- The GX Transceiver Channel 26
- The GT Transceiver Channel 27
- Receiver PMA 28
- DeserializerCDR 28
- Advanced Transmit (ATX) PLL 29
- Fractional PLL (fPLL) 29
- Calibration 30
- • Calibration on page 7-1 31
- • Arria 10 Device Datasheet 31
- Transceiver Design Flow 33
- Configure the PHY IP Core 35
- Generate the PHY IP Core 36
- Select the PLL IP Core 36
- Configure the PLL IP Core 38
- Generate the PLL IP Core 39
- Create Reconfiguration Logic 39
- Connect Datapath 40
- Compile the Design 40
- Verify Design Functionality 41
- Configuration 42
- Protocol Preset 42
- Transceiver Configuration 52
- PMA Parameters 54
- Parameters Value Description 58
- Enhanced PCS Parameters 60
- Standard PCS Parameters 70
- PCS Direct 77
- PMA Ports 80
- Name Direction Clock Domain 84
- Enhanced PCS Ports 85
- Name Bit Functionality 94
- Standard PCS Ports 99
- Name Direction Clock 105
- Description 105
- Related Information 105
- IP Core File Locations 106
- Interlaken 107
- Altera Corporation 108
- Send Feedback 108
- Reset Controller 118
- Design Example 121
- Parameter Value 122
- Ethernet 128
- Rate Match FIFO for GbE 134
- Parameters Value 139
- Transceivers 148
- Parameter Range 151
- Idle Deleted 155
- Before Deletion 155
- After Deletion 155
- 10GBASE-KR PHY IP Core 156
- Name Range Description 162
- Name Value Description 163
- 10GBASE-KR PHY Interfaces 164
- Avalon-MM Register Interface 170
- Creating a 10GBASE-KR Design 192
- Simulation Support 194
- Item Description 195
- Native PHY 197
- Clock and Reset Interfaces 198
- 1G/10GbE PHY Interfaces 206
- Register Definitions 214
- Bit R/W Name Description 215
- Addr Bit R/W Name Description 233
- Creating a 1G/10GbE Design 239
- Design Guidelines 240
- Channel Placement Guidelines 240
- XAUI PHY IP Core 242
- XAUI Supported Features 245
- XAUI PHY Release Information 247
- Device Family Support 248
- Parameterizing the XAUI PHY 249
- XAUI PHY Ports 251
- XAUI PHY Interfaces 251
- Soft PCS 253
- Acronyms 258
- PCI Express (PIPE) 259
- Supported PIPE Features 260
- Gen1/Gen2 Features 261
- Power States Description 262
- Gen3 Features 266
- PCIe Gen3 Capability 267
- Mode Enabled 267
- Gen1 Gen2 Gen3 267
- • PIPE Design Example 275
- Gen1 PIPE Gen2 PIPE Gen3 PIPE 277
- Native PHY IP Ports for PIPE 285
- Figure 2-92: x4 Configuration 294
- Figure 2-93: x8 Configuration 295
- TX PLL Selection for CPRI 300
- Auto-Negotiation 300
- Supported Features for CPRI 301
- Other Protocols 310
- TX Bit Slip 320
- TX Polarity Inversion 320
- RX Bit Slip 320
- RX Polarity Inversion 321
- Word Aligner Manual Mode 323
- RX Bit Reversal 328
- RX Byte Reversal 329
- Parameter Value Description 330
- 8B/10B Encoder and Decoder 333
- 8B/10B TX Disparity Control 334
- TX Bit Reversal 336
- TX Byte Reversal 336
- Arria 10 GT Channel Usage 344
- Transceiver PHY IP 345
- NativeLink Simulation Flow 354
- Define Control Signals Using 356
- Custom Simulation Flow 359
- How to Generate Scripts 361
- Simulator Simulation File Use 362
- PLLs and Clock Networks 364
- ATX PLL IP Core 369
- Parameter Range Description 370
- Parameters Range Description 378
- Instantiating CMU PLL IP Core 386
- CMU PLL IP Core 387
- Input Reference Clock Sources 390
- Receiver Input Pins 392
- Transmitter Clock Network 393
- GT Clock Lines 398
- Clock Generation Block 399
- Transmitter Standard PCS 404
- Transmitter PMA 404
- Clock Generation Block (CGB) 404
- Receiver Standard PCS 406
- Channel Bonding 407
- PMA and PCS Bonding 408
- Skew Calculations 410
- Using PLLs and Clock Networks 412
- Bonded Configurations 416
- Implementing PLL Cascading 420
- Mix and Match Example 422
- When Is Reset Required? 427
- How Do I Reset? 427
- Recommended Reset Sequence 428
- min 20 ns 429
- Status Signals 433
- Control Signals 433
- Arria 10 PMA Architecture 448
- Transmitter Buffer 449
- 85Ω, 100Ω, OFF 450
- Receiver 451
- Receiver Buffer 452
- High Data Rate Mode 454
- Receiver Equalization Modes 459
- Channel PLL 461
- CDR Lock Mode 462
- Loopback 463
- Transmitter Datapath 466
- Interlaken Frame Generator 468
- Interlaken CRC-32 Generator 468
- 0 0 066676767 469
- Pattern Generators 470
- S0 S1 S4 S5 S8 471
- PRBS Output 471
- Scrambler 472
- (tx_clkout) 474
- KR FEC Blocks 475
- Receiver Datapath 476
- Descrambler 477
- Interlaken Frame Synchronizer 477
- PRBS Error 478
- PRBS datain 478
- Interlaken CRC-32 Checker 479
- Enhanced PCS RX FIFO 479
- Case Word Input Output 482
- RX KR FEC Blocks 483
- Byte Serializer 485
- 8B/10B Encoder 487
- RX Polarity Inversion Feature 496
- Rate Match FIFO 496
- 8B/10B Decoder 497
- Byte Deserializer 499
- PIPE Interface 503
- Clock Data Recovery Control 504
- Reconfiguration 505
- Reconfiguration Features 507
- Configuration Files 510
- Bit Position Description 511
- Instance 512
- Arbitration 515
- Direct Reconfiguration Flow 517
- Maximum Pre-Emphasis Settings 518
- Address Bit Values 521
- Switching Transmitter PLL 523
- Switching Reference Clocks 524
- ATX Reference Clock Switching 525
- Ports and Parameters 528
- On-Die Instrumentation 535
- Address Bits Read / 536
- Feature Description 536
- Start Pattern Checker 543
- Embedded Debug Features 544
- Control and Status Registers 545
- PRBS Soft Accumulators 548
- ODI Acceleration Logic 549
- Unsupported Features 562
- Calibration Registers 564
- ATX PLL Calibration Registers 566
- Capability Registers 566
- Power-up Calibration 567
- User Recalibration 569
- Calibration Example 570
- Fractional PLL Recalibration 571
- CDR/CMU PLL Recalibration 571
- PMA Recalibration 571
- Check Calibration Status 574
- Analog Parameter Settings 575
- XCVR_A10_RX_LINK 578
- XCVR_A10_RX_TERM_SEL 579
- XCVR_VCCR_VCCT_VOLTAGE - RX 580
- CTLE Settings 580
- XCVR_A10_RX_ONE_STAGE_ENABLE 582
- VGA Settings 583
- XCVR_A10_RX_ADP_DFE_FXTAP 584
- XCVR_A10_TX_LINK 585
- XCVR_A10_TX_COMPENSATION_EN 586
- XCVR_VCCR_VCCT_VOLTAGE - TX 587
- XCVR_A10_TX_SLEW_RATE_CTRL 587
- Value Description 589
- Transmitter VOD Settings 593
- XCVR_A10_REFCLK_TERM_TRISTATE 594
- LVDS TRISTATE_ON/TRISTATE_OFF 595
- Assign To 595
- Reference clock pin 595
- Subscribe 596
- Chapter Document 607
- Changes Made 607
- Date Version Changes 626
Prodotti e manuali riguardandi Software Altera PHY IP Core
Software Altera UG-01080 Guida Utente
(702 pagine)
(702 pagine)
Software Altera PHY IP Core Guida Utente
(230 pagine)
(230 pagine)
Software Altera UG-01080 Guida Utente
(120 pagine)
(120 pagine)
Software Altera DE2-115 Guida Utente
(107 pagine)
(107 pagine)
Software Altera UG-01080 Guida Utente
(484 pagine)
(484 pagine)
ShelterLogic 72874.0 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non ShelterLogic 72874.0.
Nous fournissons des manuels en pdf 1 ShelterLogic 72874.0 à télécharger gratuitement par type de document : Manuel d'instructions
Shelterlogic 72874.0 Manuel d'instructions (9 pages)
marque: Shelterlogic | Catégorie: No info | Taille: 0.87 MB |
Table des matières
Plus de produits et de manuels pour Non ShelterLogic
| Modèles | Type de document |
|---|---|
| 25712 |
Manuel d'instructions
 
ShelterLogic 25712 Instructions / Assembly,
1 pages
|
| 90478 |
Manuel d'utilisation et d'entretien
ShelterLogic 90478 Use and Care Manual,
1 pages
|
| 90490 |
Manuel d'utilisation et d'entretien
ShelterLogic 90490 Use and Care Manual,
1 pages
|
| 70593 |
Manuel d'instructions
ShelterLogic 70593 Instructions / Assembly,
16 pages
|
| 70560 |
Manuel d'utilisation et d'entretien
ShelterLogic 70560 Use and Care Manual,
1 pages
|
| 62693.0 |
Manuel d'instructions
ShelterLogic 62693.0 Instructions / Assembly,
27 pages
|
| 73432.0 |
Manuel d'instructions
ShelterLogic 73432.0 Instructions / Assembly,
6 pages
|
| 72814 |
Manuel d'utilisation et d'entretien
ShelterLogic 72814 Use and Care Manual,
1 pages
|
| 10077.0 |
Manuel d'instructions
ShelterLogic 10077.0 Instructions / Assembly,
9 pages
|
| 95360 |
Manuel d'utilisation et d'entretien
ShelterLogic 95360 Use and Care Manual,
1 pages
|
| 62807 |
Manuel d'utilisation et d'entretien
ShelterLogic 62807 Use and Care Manual,
1 pages
|
| 82144 |
Manuel d'utilisation et d'entretien
ShelterLogic 82144 Use and Care Manual,
1 pages
|
| 70652 |
Manuel d'utilisation et d'entretien
ShelterLogic 70652 Use and Care Manual,
1 pages
|
| 90460 |
Manuel d'utilisation et d'entretien
ShelterLogic 90460 Use and Care Manual,
1 pages
|
| 10471.0 |
Manuel d'utilisation et d'entretien
ShelterLogic 10471.0 Use and Care Manual,
15 pages
|
| 77824.0 |
Manuel d'instructions
ShelterLogic 77824.0 Instructions / Assembly,
18 pages
|
| 90396 |
Manuel d'instructions
ShelterLogic 90396 Instructions / Assembly,
27 pages
|
| 62807 |
Manuel d'instructions
ShelterLogic 62807 Instructions / Assembly,
36 pages
|
| 71814 |
Manuel d'utilisation et d'entretien
ShelterLogic 71814 Use and Care Manual,
1 pages
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale