Altera DSP Development Kit, Stratix V Edition Manuale Utente Pagina 53
- Pagina / 58
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Appendix A: Programming the Flash Memory Device A–3
Programming Flash Memory Using the Board Update Portal
July 2013 Altera Corporation DSP Development Kit, Stratix V Edition
User Guide
Programming Flash Memory Using the Board Update Portal
Once you have the necessary .flash files, you can use the Board Update Portal to
reprogram the flash memory. Refer to “Using the Board Update Portal to Update User
Designs” on page 5–2 for more information.
1 If you have generated a .sof that operates without a software design file, you can still
use the Board Update Portal to upload your design. In this case, leave the Software
File Name field blank.
Programming Flash Memory Using the Nios II EDS
The Nios II EDS offers a nios2-flash-programmer utility to program the flash memory
directly. To program the .flash files or any compatible S-Record File (.srec) to the
board using nios2-flash-programmer, perform the following steps:
1. Set the DIP switch SW5.3 to the off position (factory design) to load the Board
Update Portal design from flash memory on power up.
2. Attach the USB cable and power up the board.
3. If the board has powered up and the LCD displays either Connecting... or a valid IP
address (such as 152.198.231.75), proceed to step 8. If no output appears on the
LCD or if the Config Done LED (D17) does not illuminate, continue to step 4 to
load the FPGA with a flash-writing design.
4. Launch the Quartus II Programmer to configure the FPGA with a .sof capable of
flash programming. Refer to “Configuring the FPGA Using the Quartus II
Programmer” on page 6–25 for more information.
5. Click Add File and select <install
dir>\kits\stratixVGS_5sgsmd5kf40_dsp\factory_recovery\s5gsmd5kf40_dsp_
bup.
6. Turn on the Program/Configure option for the added file.
7. Click Start to download the selected configuration file to the FPGA. Configuration
is complete when the progress bar reaches 100%. The Config Done LED (D17)
illuminates indicating that the flash device is ready for programming.
8. On the Windows Start menu, click All Programs > Altera > Nios II EDS > Nios II
Command Shell.
9. In the Nios II command shell, navigate to the <install
dir>\kits\stratixVGS_5sgsmd5kf40_dsp\factory_recovery directory (or to the
directory of the .flash files you created in “Creating Flash Files Using the Nios II
EDS” on page A–2) and type the following Nios II EDS command:
nios2-flash-programmer --base=0x0 <yourfile>_hw.flash r
10. After programming completes, if you have a software file to program, type the
following Nios II EDS command:
nios2-flash-programmer --base=0x0 <yourfile>_sw.flash r
11. Set the DIP switch SW5.3 to the on position (user design) and power cycle the
board.
Programming the board is now complete.
- User Guide 1
- Contents 3
- Additional Information 5
- 1. About This Kit 7
- Hardware 8
- Software 8
- The Development Kit Installer 9
- 1–4 Chapter 1: About This Kit 10
- Kit Features 10
- 2. Getting Started 11
- References 12
- 3. Software Installation 13
- Note to Figure 3–1: 15
- 4. Development Board Setup 17
- Note to Table 4–1: 19
- On-Board USB-Blaster II page 20
- Note to Table 4–4: 21
- 5. Board Update Portal 23
- 6. Board Test System 25
- Preparing the Board 26
- Running the Board Test System 26
- Using the Board Test System 27
- MAX V Registers 28
- JTAG Chain 29
- Flash Memory Map 29
- The GPIO Tab 30
- The Flash Tab 31
- The DDR3 Tab 33
- Error Control 34
- Data Type 34
- Read and Write Control 34
- The QDRII+ Tab 35
- Performance Indicators 36
- The XCVR1 Tab 37
- PMA Setting 38
- The XCVR2 Tab 40
- The XCVR3 Tab 43
- The Power Monitor 45
- General Information 46
- The Clock Control 47
- Set New Frequency 49
- CFI Flash Memory Map 51
- 20C0000 52
- ./restore.sh r 54
- Info–2 Additional Information 58
- Typographic Conventions 58
Prodotti e manuali riguardandi Strumenti di misura Altera DSP Development Kit, Stratix V Edition
Strumenti di misura Altera High-Speed Development Kit, Stratix GX Edition Manuale Utente
(140 pagine)
(140 pagine)
Strumenti di misura Altera MAX II Manuale Utente
(38 pagine)
(38 pagine)
Strumenti di misura Altera Low Latency 40-Gbps Ethernet MAC and PHY MegaCore Manuale Utente
(196 pagine)
(196 pagine)
Strumenti di misura Altera JNEye Manuale Utente
(194 pagine)
(194 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale